SPARKY FORUM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sparkyadmin

Pages: [1] 2 3 ... 7
1
VANA PLAYER / Re: Impossible to make it work
« on: November 23, 2017, 11:02:58 PM »
Hi,

   Have you getting any error while flashing volumio image to SD CARD?

And while connecting the power, Power LED is glowing?

With Regards
Sparky Admin

2
PIANO HI-FI DAC 2.1 / Re: Allo Piano 2.1 + Max2play volume
« on: November 22, 2017, 10:08:13 PM »
Hi,

    Can you please share the "alsamixer" details.

You can login through ssh and enter  alsamixer then you will get the details.

Username:root
password:max2play


Please find the below link for your reference.(refer alsamixer part)

You have to increase digital tab option as shown in below link

https://www.amazon.com/clouddrive/share/vLk3XO9HOt3sStRUBpf4jwaX7k6J0Im91vo4z2FWVPV/kpNKOllIRculaySb1Xaqzw?_encoding=UTF8&mgh=1&ref_=cd_ph_share_link_copy

With Regards
Sparky Admin

3
Technical Questions / Re: How to enable I2C?
« on: November 20, 2017, 01:11:09 AM »
Hi,

  On sparky  i2c 2 using , not i2c 0,i2c 2 uses on 40 pin 3 and 5. All the modules are available , no need to edit config.txt

With Regards
Sparky Admin

4
VANA PLAYER / Re: Impossible to make it work
« on: November 19, 2017, 09:00:50 PM »
Hi,

    Dont go with 16GB SD card.Take new 8gb sd card and flash volumio image from below link(download volumio image for sparky board)

https://volumio.org/get-started/

And burn the image using win32diskimager And check the status.

With Regards
Allo Support

5
Technical Questions / Re: How to enable I2C?
« on: November 17, 2017, 05:52:42 AM »
Hi,

    Please refer below link for OLED configuration in sparky.

https://github.com/sparky-sbc/sparky-test/tree/master/oled_test/sh1106

With Regards
Sparky Admin

6
Technical Questions / Re: How to enable I2C?
« on: November 14, 2017, 11:25:01 PM »
Hi,

   In latest volumio I2C is already enabled.Can you please share OLED part number or part details ?

With Regards
Sparky Admin

7
VANA PLAYER / Re: Impossible to make it work
« on: November 12, 2017, 08:54:18 PM »
Hi.
   Please take new sd card and download volumio image for sparky from below link.

https://volumio.org/get-started/

And burn the image using win32diskimager And check the status.

With Regards
Allo Support

8
Technical Questions / Re: 19V POWER SUPPLY - dimensions
« on: October 17, 2017, 01:53:32 AM »
Hi,

   Please find the dimensions details from below link.

http://61.12.17.162:9098/19VDC3.15A_PSU_DIMENSION.pdf

With Regards
Sparky Admin


9
Technical Questions / Re: RELAY ATTENUATOR - audio swich
« on: October 16, 2017, 10:31:10 PM »
Hi,

    Can I swich audio input or output on relay attenuator?

Can you provide more details on above query.

     Now the setup is working with onboard connectors (From DAC to Attenuator and From Attenuator to Volt Amp). There is no switching between the RCA connectors and onboard connectors. If you go with RCA connectors(Input & Output) of attenuator, then you have to make the attenuator as the stand alone. but in this case you have to connect some control gpio’s from the Piano or BOSS DAC through external cabling or wiring. And the same way you have to connect the RCA output to VOLT AMP.

With Regards
Sparky Admin

10
Technical Questions / Re: 19V POWER SUPPLY - dimensions
« on: October 16, 2017, 10:13:23 PM »
Hi,

   Please find the dimension details

DC Male Jack: 3mm x 6.5mm

With Regards
sparky Admin

11
KALI RECLOCKER / Re: RPI+ISOLATOR+KALI Connections?
« on: September 29, 2017, 05:02:38 AM »
Hi,

   You need to give power supply for RPI and KALI board.No need to connect battery or power supply to the isolator board.

With Regards
Sparky Admin


12
Technical Questions / Re: Power for Boss+Volt
« on: September 14, 2017, 05:29:32 AM »
Hi,

     You can use the PSU of RPI for RPI+Boss and separate 19V PSU to power the Volt board.

Or if you are buying Dual LLC you can connect 5 volt to RPI board and 19 volt supply to volt board.


With Regards
Sparky Admin

13
Technical Questions / Re: Power for Boss+Volt
« on: September 14, 2017, 04:06:49 AM »
Hi,

    No need of Dual LLC PSU for boss+volt board.Volt board requires 19 V power supply.

Dual LLC board included CM.

Can you explain how you are connecting boss+volt bundle ?on top RPI?


With Regards
Sparky Admin

14
Technical Questions / Re: Allo Boss on Rpi zeroW?
« on: September 04, 2017, 08:43:47 PM »
Hi,

   Allo boss will work with RPI Zero W.

With Regards
sparky Admin

15
Hi,

   You have to download sparky_sd_vana_1_4_100817 image from allo site then you have to burn the image to your SD card.

You should have Ethernet LAN ,then only squeezebox player will work.

Please find the link for both Vanaplayer technical and configuration manual

https://www.amazon.com/clouddrive/share/KYAb09spstOekhrnHNJ6EaQU56yjEKgz4jrQOeNxo0i?ref_=cd_ph_share_link_copy

https://www.amazon.com/clouddrive/share/KYAb09spstOekhrnHNJ6EaQU56yjEKgz4jrQOeNxo0i?ref_=cd_ph_share_link_copy

You can use volumio ,dietpi images also

With Regards
Sparky Admin


Pages: [1] 2 3 ... 7