Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - sparkyadmin

Pages: 1 ... 5 6 [7] 8
CAPACITANCE MULTIPLIER / Re: Earth connection on fixing hole?
« on: December 14, 2016, 10:32:17 PM »
Dear Team,

      In general no need of earth connection for CM board. If you wanted to connect earth then you have to connect the shielded mounting hole(Conductive path) with metallic spacers.But we are providing only plastic spacers.

With Regards
Sparky Admin

General Questions / Re: OMAP4 Issue on Ubuntu
« on: December 13, 2016, 10:05:55 PM »
Dear Team,

   It is not OMAP4 based SBC.

With Regards
Sparky Admin

KALI RECLOCKER / Re: External oscyllators and multifrequency
« on: December 11, 2016, 11:25:52 PM »
Dear Team,

Yes.You can change the external oscillators(on board) for MCLK. Corrently  we are assembled on board oscillators are 45.15850Mhz and 49.15200Mhz  from NDK.

So if you want, you can change any oscillator with 44.1Khz and 48Khz family. But you have to remove and solder the Oscillators manually and the oscillators should be same footprint.

Please find the attached image for the same

With Regards
Sparky Admin

VOLT AMP shield / Re: Pwr problem on Volt AMP
« on: December 06, 2016, 04:02:19 AM »
Dear Team,

     Please check by connecting 19 v directly to the Volt Amp shield and check weather it is coming up or not.

With Regards
Sparky Admin

VOLT + standalone AMP / Re: Volt+ as power amp...
« on: November 16, 2016, 01:48:14 AM »

Please find the attached document for by pass the volume control in VOLT+ board.

With Regards
Sparky Admin

VOLT + standalone AMP / Re: AM Avoidance switch...
« on: November 02, 2016, 11:54:29 PM »
Hello ,

AM Avoidance Switch Settings info attached in the screen shot.



VOLT + standalone AMP / Re: Volt+ as power amp...
« on: November 02, 2016, 06:08:13 AM »
Hello ,

We don't have option to by pass the volume control,it may required manual soldering if you really wanted to do that.



PIANO HI-FI DAC / Re: Sparky ubuntu download to run the dac piano?
« on: November 02, 2016, 06:01:08 AM »
Hello ,

Linux Distribution supported on Sparky -: Ubuntu 12.04 - 3.10.37

Kindly explain your setup ? you have Sparky + Piano ?



General Questions / Re: Support for Third Party RTC
« on: November 02, 2016, 04:50:10 AM »
Dear Rajesh ,

Sparky support RTC ,No third party RTC unit required,only need battery connection

But only custom designed sparky will support RTC. RTC's  specific circuitry to support RTC .



PIANO HI-FI DAC 2.1 / Re: Ho w to configure to 2.0?
« on: October 27, 2016, 10:53:26 PM »
In Piano 2.1 1st two RCA is general LEFT -Right stereo OUT ,Sub woofer in the next two RCA

KALI RECLOCKER / Re: ALLO Reclocker differnet Version
« on: October 26, 2016, 02:03:46 AM »
1) The exact frequency values for the Oscillators are (22.5792Mhz/24.576Mhz)  &  (45.1584Mhz/49.152Mhz)
    2) Both the versions supports at most of the mp3 files.
    3) Only different between 45/49 version and 22/24 version is, in 22/24 version ,it supports upto 176.4K(44.1k family) and 192k(48k family)   sampling rate audio files.But in case of 45/49 version supports above 176.4k(44.1k family) and 192k (48k family).
   4) And both the versions ,it wouldn't degrade any audio quality.Because both the versions of Oscillators(from NDK) having very low jitter (3-5ps).

hope this helps ..

KALI RECLOCKER / Re: Identifying 44/48MHz or 22/24Mhz version...
« on: October 26, 2016, 02:02:12 AM »
    45 /49 version Boards Oscillator marking:

    45.1584Mhz  ----> D45.158 621: VG/3F
    49.152Mhz    ----> D49.152 622:2G/BD

   22 /24 version Boards Oscillator marking:

    22.5792Mhz  ---> D22.579 617: A8/D8
    24.576Mhz    ---> D24.576 617: SB/X

KALI RECLOCKER / Re: Kali 'Hat size Not Hat Compliant'
« on: October 26, 2016, 02:01:28 AM »
The Kali page shows a badge saying 'Hat size Not Hat Compliant'. Does that mean it's not compatible with the Raspberry PI?

Hat size -: mounting holes and connectors will match with RPI
Hat Compliant -: Still under process but it support with RPI

what are the jitter accuracy measurements of Kali?

3 to 5 ps

How is an 'external Crystal Oscillators for MCLK or upgraded to a higher quality, multi-frequency clock that comes with automatic Fs switching and better performance' fitted?

Automatic FS switching -according to the Audio sampling rate KALI will select (ON BOARD) external Crystal Oscillators MCLK

VOLT + standalone AMP / Re: Volt + Power socket...
« on: October 25, 2016, 04:06:12 AM »
Dear Suresh ,

Volt + use 3 mm DC power jack .

Sorry ,We dont have any option for power ON and OFF on board .



General Questions / Re: OMAP4 Issue on Ubuntu
« on: October 25, 2016, 03:37:52 AM »
Hello ,

Did you observed OMAP4 issues while doing apt-get update ?



Pages: 1 ... 5 6 [7] 8